Specials 
Products 
Industrial 
Test Stands 
Components 
Mules 
Aircraft/
Aerospace 
Power
Supplies 
Hydraulic
Pumps 
Motion
Picture
Special
Effects |
Need GPU's? Call for details on Stewart Stevenson 60 and 90 KVA units. Also Sprague 60 KVA. Let us hear from you....
your required items may not be listed within these pages.
| AGTS-101 | Auto Generator Alternator Starter |
| Sun Electric PN C619-1000 Model AGT-9A 220/440 volt 60 hz. 3 phase 22-1/2 HP 800-11,000 RPM excellent condition |
| CSDS-101 | Constant Speed Drive Starter Test Unit |
To test starter generators used on aircraft or automobiles
Consists of 4 sections:
 | Control panel | | Oil Cooler system | | Starter mounting system | | Hydraulic system |
PN 284300-2 by Allied Signal approx. 2000 lbs. wt. |
A desk type unit which contains operating instrumentation to evaluate condition of equipment under test.,
Test aircraft generators, regulators, constant speed drives
Rated 115/200 vac, 3 phase 400 CPS up to 90 KVA at 10 to 0.75 (lagging) P.F. 3000 to 9000 RPM, CW or CCW rotation
Test stand power requirement is 220/240 volt 3 phase 60 hz.
Drive motor 125 HP Gear unit 1:3.5 speed increase ratio. |
| T-1182-200 | GREER Serial JJH-1 75 HP Fuel Pump Test Stand |
| Rotating/Flushing Drive speed RPM gauge 100-800 to 5 HP drive pad - GREER MFG. Model RP1166-5-200 (PWA 6437) front and back gauges. Reliance Motor |
| TS-119 | Hydraulic (Type HCT6) w/ Pump Test capabilities |
Unit is rated:
15 GPM 5000 PSI for flow testing and 25 GPM 5000 PSI 500-5000 RPM for pump testing.
Currently MIL-H-5606 fluid service (red oil). Skydrol convertible. |
| TS-120 | Accumulator Proof & Burst Test Stand |
| BECON #501-RATED 0-30,000 PSIG FLUID AND O-9000 PSIG NITROGEN. Originally designed for testing accumulators and high pressure assemblies. Stand has "Water Bath" for pneumatic bubble testing as well as O-30,000 PSI Hydrostatic. |
| TS-122 | BENDIX Turbine Drive Gear Box Tester #53E46-1A |
| Ideal for high speed rotational testing of pumps, tachometer generators and small aircraft items. Unit is rated 3 to 5 HP and 12,000 RPM using solid state control and digital read-out |
| Mfgr. Haskell Engineering O-9000 PSI Air with flowmeters. Gauges, valves, test chamber, regulators, for safe pneumatic testing. |
| TS-133 | Fuel Injector Pump Tester |
by Hydraulics International
NSN 4910-01-037-9417
Unit is complete with 12 paternators and flow section, pressure gauges, regulators, valves included |
| TS-135 | Hose Proof & Burst Test Stand |
5000 PSI with 6" x 6" x 2 ft. test chamber. WILL TEST 1/4" TO 2" hose.
Unit by Aeroquip. Used, excellent condition |
| TS-136 | 75 HP Aircraft Jet Engine Fuel Pump Test Stand Console |
| TS-137 | 40 GPM Hydraulic Test Stand TYPE KG-100 |
GREER MANUFACTURING
To test new or newly overhauled hydraulic system components such as relief valves, actuating cylinders, pressure regulators, brake valves, etc. Flows up to 40 GPM and pressures up to 5000 PSI. Dual shaft 75 HP electric motor which drives two 20 GPM variable delivery pumps.
Ask for photo and details. |
| TS-138 | Universal Hydraulic Test Stand w/ Pump Test Drive Section |
| 30 GPM 3000 PSI AVITECH #AV843 designed for valves, actuating cylinders, solenoid valves, reservoirs, accumulators and pumps. Red Oil fluid. Hydrostatic Test circuit 25,000 psig maximum pressure |
| PN 1333-100 7-1/2 GPM 5000 PSI Can be up-graded to 10 GPM. Has stainless steel plumbing and reservoir 600 series Denison pump 15 HP 1200 RPM motor. Manual 4 way valve cycling circuits for extending and retracting hydraulic cylinders. Sliding Lexan shield across full length of stand. D.C. power supply included |
| TS-141 | ABEX Dual Station Stationary Hydraulic TYPE SK1674 |
| Combination to supply various ports to operate an item under test. System does not include the hydraulic power supply, however, one can be included with the item. Just advise us if you want quote WITH OR WITHOUT hydraulic supply. The stand is intended to be used inside a test lab...and a hydraulic power unit to be located in a pump room. Can convert to Skydrol |
| TS-142 | VICKERS Hot Oil Test Stand |
PN 653827A NSN: 4920-00-626-5924
20 gpm 50 hp 3550 RPM Drive motor 220/440 v. Vickers A12905 series variable volume pressure compensated pump 5000 PSI. Work sink area 2 ft. square. Walter Kidde circuits for Fire control CO2 nozzle included. |
Manufactured by Sundstrand PN 684668
1000 PSI working pressure. Gauges, timer, variable speed drive, Vickers pump unit on casters easy to move. |
100 GPM 3000 PSI/5000 PSI with 250 HP DC Variable pump test drive
O/6000 RPM Stainless steel reservoir 30 electronic digital system read-outs, press-flow-temp-RPM-torque, AC & DC amp and volts. System is set up for remote data acquisition. Will test aircraft or commercial pumps, motors, cylinders, valves, hoses, etc.
Mdl. AF 27T9
Mfgr: Dayton T. Brown Co. |
| TS-157 | Hydraulic Valve Test Stand Marine Fluid 2190 |
| For a variety of hydraulic valves including "SERVO" types. Originally designed for Submarine hydraulic valve testing Stand includes two (2) each 800 series Denison pumps, variable volume O-35 GPM each total flow 70 GPM |
| TS-164 | 100 HP Hydraulic Pump Test Stand - Variable Speed. |
Mfgr: General Dynamics
Currently uses red oil but we can convert to Skydrol. Ramping features, reduced voltage starters, variable frequency speed control, hydraulic load circuit. The test stand consists of two sections: Pump Drive Bench with sink and enclosure and control & instrument bench. |
Mfgr. McDonnell Douglas
20 hp electric motor 220/440 Denison pump PF005-C-632R oil cooler, reservoir, pressure tank, flow cylinder, pump motor control system work bench sink
Dim: 9 ft. L. x 6 ft. h. x 3 ft. w. |
| Dunn's Valve Tester Nominal Cap. 3000 PSI commercial type relief and pop off valve test stand and set point fixture. Complete with clamping fixture. power source: air and liquid pump. for valve test. Water or oil service. |
| TS-167 | TEST STAND 20 gpm Skydrol service |
| O-5000 PSI with 60 HP motor 60 gallon reservoir with filters 5 ft. lg.with sink. Denison 20 GPM pressure compensated pump Motor 1175 RPM 240-440 volts, 3 phase 60 hz. Test Stand power unit includes filter, heat exchanger, relief valve. Designed to test actuators, valves, pumps, hose assemblies and related components up to 5000 PSI with hydrostatic test circuit up to 10,000 PSI. Call for full details |
| TS-169 | Propeller Governor Test Stand |
| Mounting for Governor - 2 drive pads, pressure gauges, timer proportional controller |
| TS-173 | Hydraulic Pump Test Stand for Corporate Aircraft |
Sprague PN 78648 Red Oil service (can be converted to Skydrol)
1700 to 3775 RPM 40 HP Varidrive
Variable speed for open and closed loop testing.
Rotation is reversible. A hydraulic pump system can be added as remote item to test other components such as actuator valves, or main drive can serve as drive pad to pump...producing flow and pressure for other tests.
Actual photos and detailed specs on request |
| TS-174 | Hydraulic Flow Test Stand - Stationary |
Mfgr: HORKEY MOORE
Mil Red Oil service or Skydrol...if other fluid service is required ask about our Zero Time Overhaul and conversion. O-35 GPM range at pressures of O to 5000 PSIG. (above 3000 PSIG the rate of flow decreases as pressure is increased to 5000 PSIG where maximum flow capacity is 23 GPM. Static circuit with 25,000 PSI Complete with Denison main pump, variable volume, pressure compensated, gauges, reservoir, flowmeters, temp. indicators. Self contained bench type unit housed in all welded steel cabinet. Detailed data page available on request. |
| TS-175 | General Electric Fuel Pump Tester |
| originally designed for T58/T64 support. May be used for fixed wing pump testing. Test Pump drive motor super "T" power unit by Reliance. Boost pump and motor. Ingersol Rand pump and G.E. 5 hp motor. Ask for data sheet. |
| TS-176 | Kennet Hydraulic Test Stand |
| 0-10 GPM O-5000 PSI RED OIL |
PN KS2600
Self contained unit designed to test Hydromatic reversing and non-reversing propellers. It performs propeller functional tests, internal and external leakage checks. The tester can also be used to functionally test most of the propeller component valve assemblies. |
| TS-180 | Hydraulic Pump Test Console - SPRAGUE |
| Remote hydraulic power supply included. Fluid test media: Mil-H-83282 (We will convert to Skydrol at your request) Originally designed for F-18 aircraft pump Abex M/N APP19V-1. For check out test functions on hydraulic components, especially aircraft style pumps and motors at operating pressures to 3000 PSI, test pressures to 5000 PSI and static pressures to 9950 psig. Only 680 hours on unit |
| TS-181 | Hydraulic Stationary Test Stand |
Model 9770-0302
ACL 30 GPM & 5000 PSI Temp. 165 deg.max. 1400 hours on unit
Red oil fluids (We can convert to Skydrol if you require)
440 volts 3 phase 60 hz. 140 full load amps. |
| TS-182 | TS-96-BB-345 Test Stand |
| One man operation for functional testing on hydraulic manifolds, actuators, valves, pumps, hose assemblies and related components with proof test to 10,000 PSI. | | Click for Picture and Detailed Specs. |
| TS-183 | Hot Oil Flight Actuator Helicopter Test Stand |
| TS-184 | Automated Altitude Simulator Valve Test Stand |
| TS-185 | Linear Actuator Test Stand |
| King Nutronics P/N 3543-31-1 M/N 3543 Cyl. stroke 26" Bore 8" 1" NPT air da min. open 6" |
| TS-187 | MODEL 87RM233 Universal Test Stand |
Manufactured by American Lab & Systems.
Wide body aircraft components test stand rated 50 GPM designed to test actuators, valves, pumps, hose assemblies and related components to 3000 PSI with a proof test circuit to 10,000 PSI Dual System. | | Click for Picture and Detailed Specs. |
| TS-188 | ALS Series 9500 Hydraulic Shop Test Stand |
Stainless Steel Unit. Will service fixed and rotary wing aircraft. Available in 10, 20 and 30 GPM flow. Skydrol, Red Oil or Industrial oil service.
Photos, Quotes and Data sheets on request |
| TS-189 | #91-BB-305-1 Skydrol Component Test Stand |
| American Lab & Systems Model. Two sections. Stainless console with gauges, controls, selector valve, work sink sump and sump pump - complete with hydraulic power unit. O-30 GPM and O-3000 PSIG with 5000 PSI up to 10 GPM. Leading particulars available on request. |
| TSF-101 | Fuel Accessories Test Stand |
| by BAUER M/N BE13807b Overall flow capacity of 200 GPM at 177 PSIG static test capability of O-465 PSI uses 3 turbine flowmeters with flow computer to compensate for viscosity of temperature change |
| TSF-102 | Anti-icing Fuel Pump Test Stand |
| by BAUER Mfg. Part No. BMI 15340A Pratt & Whitney Aircraft Div. PN PWA-15340A self contained with cat-walk inside. Emergency sprinklers, CO2 fire control system with refrigeration unit. Fuel pump controls 9 ft. lg. 7-1/2 ft. deep 67-1/2 ft. ht. |
Originally F-14 wing sweep actuator tester. Heavy Duty - New Surplus. General Dynamics Corporation.
Capable of testing Linear and Rotary actuators with 52,000 lb. tension compression load Denison Motor MF05-020-31N-1 3500 PSI 3000 RPM |
DUAL HEAD with 30 KVA Load Bank and 600 amp DC 70 HP continuous 12 HP intermittent 2300 to 11,500 RPM. Can be modified for higher HP and RPM. Used, excellent condition.
We offer conversion from 14,000 to 18,000 RPM ranges. |
| TS-VDR-106 | BENDIX Universal Aircraft Generator Test Stand |
| P/N 60B11-1 Used excellent condition. A completely integrated testing facility which utilizes an important "feed back principle and enables the testing of two (2) generators simultaneously. |
|
Test Stands 